INSTRUCTIONS FOR USE
May be applied on:
- New and old plasters based on hydraulic binders.
- Concrete surfaces.
- Gypsum and gypsumboard surfaces.
- Old paints and wall coatings that are organic or mineral in nature, dry, compact, absorbent and cohesive.
- Mineral conglomerates of various kinds, as long as they are absorbent.
- Surfaces in wood, chipboard, plywood and similar.
Surfaces should be adequately prepared by following the instructions given in the paragraph 'PREPARING THE
SURFACE'.
Do not apply on freshly painted surfaces

TECHNICAL SPECIFICATIONS
-Type of binder: acrylic resins in aqueous emulsion
-Specific gravity per UNI EN ISO 2811-1: 1.07 ± 0.05 kg / l
-Classification of reaction to fire EN13501-1: Class A2 s1 d0
Referred to a consumption not exceeding that indicated, and to an application on a non-combustible surface.
-Drying (at 25 °C and 65% RH): dust 30 min.; touch 2 hours.

PREPARING THE SURFACE
Plaster, gypsum and gypsum board surfaces:
- Make sure that the surface is thoroughly dried and aged. Resurface or consolidate using specific products if
necessary.
- If mold is present, treat the surface with COMBAT 222 cleanser code 4810222, and with COMBAT 333
reconstruction code 4810333. To protect the wall from mold formation add COMBAT 444 code 4810444 sanitizer to the product.
- Brush or wash to remove any efflorescence and any old peeling paint. Completely eliminate any raised layers of lime-based or tempera paints.
- Remove any dust, smog or other deposits by brushing.
- Level any irregularities in the surface and treat holes, cracks, crevices and gaps with TAMSTUCCO
9400006/9410110; sand putty and touch-ups with sandpaper.
- Use adequate sealants to seal any cracks.
- Smooth if necessary with RASAMIX 9440160 or with BETOMARC 9450150 or RASOMARC 9500150 according
to the type of support.
- On a clean, dry surface apply one coat of IDROFIS 4700006 acrylic water-based wall fixative or ATOMO
8840001 micronized solvent-free fixative. On gypsumboard, apply the specific fixative PREPARA 4710019 pigmented fixative
- Apply the primer chosen for the realization of the effect desired.
- Apply MY_ART as described in the application instructions.\

APPLICATION INSTRUCTIONS
- Air and support surface conditions:
Air temperature: Min. +8 °C / Max. +35 °C
Relative environmental humidity: <75%
Support surface temperature: Min. +5 °C / Max. +35 °C
Moisture level of the support surface: <10%
- Tools: brush.
- Number of coats: One or more layers according to the desired effect.
- Dilution: 10% max.
- Cleaning of tools with water immediately after use.
Method of application:
Apply the product and process it directly with the chosen tool.
For applications with a plastic spatula is recommended to first spread the product with a brush.
Indicative spreading rate: 15-20 m2/l depending on the decorative base used.
The consumption of the material varies considerably depending on the type of effect realized. In the case of
large-scale work, we recommend a preliminary test.

TINTING
Product is neutral and is compatible with the colouring pastes of the Marcromie tinting system.
Do not exceed the maximum amount of 5% by volume of tinting pastes.

STORAGE
Maximum temperature for storage: +30 ºC.
Minimum temperature for storage: +5 ºC.
The product should be preferably used within 2 years from date of manufacture when stored in original unopened containers and in appropriate temperature conditions.

SAFETY RULES
Limit value EU (Dir. 2004/42/EC)
Cat. A/l: Decorative effect coatings (water-base): 200 g/l (2010)
MY_ART Contains max: 200 g/l VOC
The product does not require labeling in accordance with the regulations in force. Use the product according to current standards of hygiene and safety after use, do not litter containers, allow the residue to dry and treat them as special waste. Keep out of the reach of children. If swallowed, seek medical advice immediately and show this container or label. Do not empty into drains, water courses or onto the ground.

SPECIFICATION ITEM
Decorative finish made of acrylic copolymer in water emulsion.
Apply MY_ART 454 series of previously prepared surfaces in the coats and the quantities determined by the surface and the aesthetic desired effect.